PWM Solar Charge Controllers

GlowTech PWM Pulse Width Modulation charge controller for solar systemsWhat is PWM?

Pulse Width Modulation (PWM) is the most effective means to achieve constant voltage battery charging by switching the solar system controller’s power devices. When in PWM regulation, the current from the solar array tapers according to the battery’s condition and recharging needs.Morningstar Sunsaver 20L-20L-12v PWM charge controller

If you want to just get to the bottom line, skip to the bottom of the article and read the red highlighted text.

If you read the entire article you will understand the technology behind why PWM is the only real way to go when it comes to solar charge controllers.

Why is there so much excitement about PWM?

Charging a battery with a solar system is a unique and difficult challenge. In the old days, simple on-off regulators were used to limit battery outgassing when a solar panel produced excess energy. However, as solar systems matured it became clear how much these simple devices interfered with the charging process.

The history for on-off regulators has been early battery failures, increasing load disconnects, and growing user dissatisfaction. PWM has recently surfaced as the first significant advance in solar battery charging.

PWM solar chargers use technology similar to other modern high quality battery chargers. When a battery voltage reaches the regulation setpoint, the PWM algorithm slowly reduces the charging current to avoid heating and gassing of the battery, yet the charging continues to return the maximum amount of energy to the battery in the shortest time. The result is a higher charging efficiency, rapid recharging, and a healthy battery at full capacity.

In addition, this new method of solar battery charging promises some very interesting and unique benefits from the PWM pulsing. These include:

  1. Ability to recover lost battery capacity and desulfate a battery.
  2. Dramatically increase the charge acceptance of the battery.
  3. Maintain high average battery capacities (90% to 95%) compared to on-off regulated state-of-charge levels that are typically 55% to 60%.
  4. Equalize drifting battery cells.
  5. Reduce battery heating and gassing.
  6. Automatically adjust for battery aging.
  7. Self-regulate for voltage drops and temperature effects in solar systems.
How does this technology help me?

The benefits noted above are technology driven. The more important question is how the PWM technology benefits the solar system user.

Jumping from a 1970’s technology into the new millennium offers:

  • Longer battery life:
    • Reducing the costs of the solar system
    • Reducing battery disposal problems
  • More battery reserve capacity:
    • Increasing the reliability of the solar system
    • Reducing load disconnects
    • Opportunity to reduce battery size to lower the system cost
  • Greater use of the solar array energy:
    • Get 20% to 30% more energy from your solar panels for charging
    • Stop wasting the solar energy when the battery is only 50% charged
    • Opportunity to reduce the size of the solar array to save costs
  • Greater user satisfaction: get more power when you need it for less money!!
Are all of these benefits tested and proven?

A great deal of testing and data supports the benefits of PWM.

Are all PWM chargers the same?

Buyer beware! Many solar charge controllers that simply switch FETs differently than the on-off algorithm claim to be a PWM charger. Only a few controllers are actually using a Pulse Width Modulated (PWM) constant voltage charging algorithm. The rest are switching FETs with various algorithms that are cheaper and less effective.

Morningstar was awarded a patent in 1997 for a highly effective battery charging algorithm based on true PWM switching and constant voltage charging. All Morningstar products use this patented algorithm.

Ability to recover lost battery capacity

According to the Battery Council International, 84% of all lead acid-battery failures are due to sulfation. Sulfation is even more of a problem in solar systems, since opportunity charging differs significantly from traditional battery charging. The extended periods of undercharging common to solar systems causes grid corrosion, and the battery’s positive plates become coated with sulfate crystals.

Morningstar’s PWM pulse charging can deter the formation of sulfate deposits, help overcome the resistive barrier on the surface of the grids, and punch through the corrosion at the interface. In addition to improving charge acceptance and efficiency, there is strong evidence that this particular charging can recover capacity that has been lost in a solar battery over time. Some research results are summarized here.

A 1994 paper by CSIRO, a leading battery research group in Australia (reference 1), notes that pulsed-current charging (similar to Morningstar controllers) has the ability to recover the capacity of cycled cells. The sulfate crystallization process is slowed, and the inner corrosion layer becomes thinner and is divided into islands. The electrical resistance is reduced and capacity is improved. The paper;s conclusion is that pulse charging a cycled battery can evoke a recovery in battery capacity.

Another paper, a Sandia National Labs study in 1996 (reference 2, attached), summarizes testing of a VRLA battery that had permanently lost over 20% of its capacity. Conventional constant voltage charging could not recover the lost capacity. Then the battery was charged with a Morningstar SunSaver controller, and ;much of the battery capacity has been recovered.

Finally, Morningstar has been testing for capacity recovery. An attached graph (reference 3, attached) shows how a battery that was dead recovered much of its lost capacity after extended charging with a SunLight controller.

After the test was set-up, for 30 days the solar lighting system produced virtually no lighting since the system went directly into LVD each night. The battery was very old and about to be recycled. Then, the load began to turn on longer each night as shown on the graph. For the next 3 months the battery capacity steadily increased. This test and other capacity recovery tests are ongoing at Morningstar.

Increase battery charge acceptance

Charge acceptance is a term often used to describe the efficiency of recharging the battery. Since solar batteries are constantly recharging with a limited energy source (e.g. opportunity charging with available sunlight), a high charge acceptance is critical for required battery reserve capacity and system performance.

Solar PV systems have a history of problems due to poor battery charge acceptance. For example, a study of four National Forest Service lighting systems (reference 4) using on-off shunt controllers clearly demonstrated the problems caused by low charge acceptance. The batteries remained at low charge states and went into LVD every night, but the battery typically accepted only about one-half the available solar energy the next day during charging. One system only accepted 10% of the energy available from the array between 11:00 AM and 3:00 PM!

After extensive study, it was determined that ;the problem is in control strategy, not in the battery. Further, the battery was capable of accepting that charge, but it wasn’t being charged. Later a system similar in all respects except using a constant voltage charge controller was studied. In this case, the battery is being maintained in an excellent state of charge.

A later study specific to Morningstar’s PWM constant voltage charging by Sandia (reference 2, attached) found that the SunSaver’s increased charge acceptance is due to the PWM charge algorithm. Tests showed that the SunSaver provided 2 to 8% more overcharge compared to a conventional DC constant voltage charger.

A number of tests and studies have demonstrated that Morningstar;s PWM algorithm provides superior battery charge acceptance. An attached graph (reference 5, attached) compares the recharging ability of a Morningstar SunSaver PWM controller with a leading on-off regulator. This study, done by Morningstar, is a side-by-side test with identical test conditions. The PWM controller put 20% to 30% more of the energy generated by the solar array into the battery than the on-off regulator.

Maintain high average battery capacities

AGM battery discharge volts state of chargeA high battery state-of-charge (SOC) is important for battery health and for maintaining the reserve storage capacity so critical for solar system reliability. An FSEC Test Report (reference 6) noted that ;the life of a lead-acid battery is proportional to the average state-of-charge, and that a battery maintained above 90% SOC can provide two or three times more charge/discharge cycles than a battery allowed to reach AGM battery depth of discharge cycle chart50% SOC before recharging.

However, as noted in the previous section, many solar controllers interfere with the recharging of the battery. The FSEC study noted at the end of the report that the most significant conclusion is that some controllers did not maintain the battery SOC at a high level, even when loads were disconnected.

In addition, a comprehensive 23 month study of SOC factors was reported by Sandia in 1994 (reference 7, page 940, attached). It was learned that the regulation setpoint has little effect on long-term SOC levels, but the reconnect voltage is strongly correlated to SOC. Five on-off regulators and two quasi constant voltage regulators were tested (Morningstar controllers were not developed when this test started). A summary of the SOC results follows:

  • 3 on-off regulators with typical hysteresis averaged between 55% and 60% SOC over the 23 month period
  • 2 on-off regulators with tighter hysteresis (risking global instability) averaged about 70% SOC
  • The 2 constant voltage controllers with hysteresis of 0.3 and 0.1 volts averaged close to 90% SOC (note that Morningstar controllers have a hysteresis of about 0.020 volts)

Sandia concluded that the number of times a system cycles off and on during a day in regulation has a much stronger impact on battery state-of-charge than other factors within any one cycle. Morningstar’s PWM will cycle in regulation 300 times per second.

It would be expected that batteries charged with Morningstar’s PWM algorithm will maintain a very high average battery state-of-charge in a typical solar system. In addition to providing a greater reserve capacity for the system, the life of the battery will be significantly increased according to many reports and studies.

Equalize drifting battery cells

Individual battery cells may increasingly vary in charge resistance over time. An uneven acceptance of charge can lead to significant capacity deterioration in weaker cells. Equalization is a process to overcome such unbalanced cells.

The increased charge acceptance and capacity recovery capabilities of PWM pulse charging will also occur at lower charging voltages. Morningstar’s PWM pulse charging will hold the individual battery cells in better balance where equalization charges are not practical in a solar system.

More testing will be done to study the potential benefits is this area.

Reduce battery heating and gassing

Clearly battery heating/gassing and charge efficiency go hand in hand. A reduction in transient gassing is a characteristic of pulse charging. PWM will complete the recharging job more quickly and more efficiently, thereby minimizing heating and gassing.

The ionic transport in the battery electrolyte is more efficient with PWM. After a charge pulse, some areas at the plates become nearly depleted of ions, whereas other areas are at a surplus. During the off-time between charge pulses, the ionic diffusion continues to equalize the concentration for the next charge pulse.

In addition, because the pulse is so short, there is less time for a gas bubble to build up. The gassing is even less likely to occur with the down pulse, since this pulse apparently helps to break up the precursor to a gas bubble which is likely a cluster of ions.

Automatically adjust for battery aging

As batteries cycle and get older, they become more resistant to recharging. This is primarily due to the sulfate crystals that make the plates less conductive and slow the electro-chemical conversion. However, age does not affect PWM constant voltage charging.

The PWM constant voltage charging will always adjust in regulation to the battery’s needs. The battery will optimize the current tapering according to its internal resistance, recharging needs, and age. The only net effect of age with PWM charging is that gassing may begin earlier.

Self-regulate for voltage drops and temperature effects

With PWM constant voltage charging, the critical finishing charge will taper per the equation I = Ae-t. This provides a self-regulating final charge that follows the general shape of this equation.

As such, external system factors such as voltage drops in the system wires will not distort the critical final charging stage. The voltage drop with tapered charging current will be small fractions of a volt. In contrast, an on-off regulator will turn on full current with the full voltage drop throughout the recharging cycle (one reason for the very poor charge efficiency common to on-off regulators).

Because Morningstar controllers are all series designs, the FET switches are mostly off during the final charging stages. This minimizes heating effects from the controller, such as when they are placed inside enclosures. In contrast, the shunt designs will reach maximum heating in the final charging stage since the shunt FETs are switching almost fully on.

In summary, the PWM constant voltage series charge controller will provide the recharging current according to what the battery needs and takes from the controller. This is in contrast to simple on-off regulators that impose an external control of the recharging process which is generally not responsive to the battery’s particular needs.

 

Copyright © AHTrimble.com ~ All rights reserved
No reproduction or other use of this content
without expressed written permission from AHTrimble.com
See Content Use Policy for more information.

Note: Thanks to ecodirect and other sources for information contained in this post.

 

 

3 thoughts on “PWM Solar Charge Controllers

  1. Beautiful, well written, couldnt have said it better myself. I have built several and currently maintain one solar array for the camping/house etc., potential issues.
    You are correct, add a solid 12v/35amphr pwm in with a 1500 watt pure syne (spl?) wave and multi facet flex panel and while it may cost a little more up front (or allot if you cant shop well) drop in between 3 and 10 12volt/35amphr batteries wired in parallel for longevity or series for power output and bam…with proper power conservation you can easily be off grid 🙂

    Its fun, easy to do and with awesome articles like this abounding across the internets a complete no brainer!

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s